|
BTM-01 StarCom1
Bluetooth Module
Introduction
Measuring only
1¼" x ¾" x 1¾"
Install with Starcom1, then leave your bluetooth enabled phone in your
pocket, it will automatically connect each time you get on the bike.
The
Starcom1 bluetooth module is designed to allow cordless and automatic
operation of bluetooth compatible mobile phones with the StarCom1 unit.
BTM-01 £89.99
$162.00
Bluetooth is a
short- range wireless communication technology. It allows wireless
connections between Bluetooth devices such as cellular phones, personal
digital assistants (PDA), desktop and notebooks computers, input-output
devices (mouse, keyboards, printers), home appliances. Bluetooth refers to a
worldwide standard designed to operate in the internationally recognized ISM
(Industrial Scientific and Medical) frequency band. Within the ISM band
(2.4Ghz - 2.48Ghz) Bluetooth transmissions hop between 79 separate
frequencies 1,600 times every second, and with a communication range of
about 10 meters (class II).
Bluetooth Class 2 product with compliance to
specification v11.1 and full FCC and CE certification.
Installation instructions must be
followed carefully.
Installations must only be undertaken by a person who has a full
understanding of the electrical, safety and mechanical requirements
involved. If in any doubt, please consult your dealer.
Unit
Installation
The unit must be operated from a switched vehicle 12V DC supply. The unit
is water-resistant but not waterproof so care must be taken to keep it
dry. Care must be taken not to mount the unit near areas which will get
hot, for example, near the engine or exhaust. Also the unit must not be
placed close to the ignition system; HT leads coil, alternator, or parts
of the bike that could cause electrical interference.
Power
Cable Installation
The unit requires a 12V vehicle supply it has a built-in voltage
regulator, reverse input protection and fuse, so that it is safe to use
directly from a vehicle’s switched supply. A power cable is supplied along
with an in-line fuse and fitting kit.
The 12V supply must be ignition switched, so that the BTM-01 supply is off
when the vehicle ignition if OFF else the vehicle battery may be drained.
The Jack plug cable must be plugged into the phone socket on
Starcom, this provides the 0V connection.
1) If the
StarCom 12V supply is ignition switched supply then the BTM-01 12V
connection can be made by splicing into the starcom power cable.
2)
If the StarCom is connected to the battery directly then the BTM-01module
must be connected to a switched supply.
Pairing Headset
You are required to pair the BTM-01 with your mobile phone or other
devices before using it.
Step 1: The BTM01 must be connected to StarCom and powered ON before
initiating pairing. To initiate
pairing, press and hold pairing button for 5 seconds until the red
indicator of BTM-01 is slowly flashing.
Step 2: Initiate pairing process of your mobile phone. Refer to the manual
of mobile phone for details of the process. You will see a new item
"StarCom1" added in your Bluetooth device list after the searching process
completes.
Step 3: You will be asked to enter pin-code to complete pairing, enter
0000 and confirm it. (Note: The 0000 is default pin-code pre-stored in
BTM-01.) The red indicator will turn off after pairing completed
successfully.
Note:
1. If the BTM-01 is not in pairing mode, your mobile phone won't find the
BTM-01.
2. You may need to repeat steps 1 to 3 until pairing succeeds.
3. Pairing is a process of associating Bluetooth devices with each other.
It will establish a permanent security link between the devices and enable
quick access to the services provided without the need to enter passkeys.
4. Paired devices remain paired even when:
- One of the devices is not powered on.
- A service connection is interrupted or the service stopped. - One or
both devices are rebooted.
Fitting Kit
5x short tie
wraps 1x scotch lock splice 1x loop Velcro 1x hoop Velcro
|
|
